Leave Your Message
Products Categories
Featured Products

NBSEROL NBEST-500P-PLUS Phase Protection Machine - Reliable China Suppliers & Factory Solutions

This machine features a loss and dislocation phase protector designed to ensure safe operation. In the event that the three-phase external power supply is incorrectly connected, the protector will automatically disconnect to prevent damage. During this safety mode, all indicators on the control panel will display regularly, and the machine will not operate. To resume functionality, please correct the power supply phase connection and restart the machine. We recommend that this operation is performed by professional electric technicians. As a reliable China factory and suppliers, we prioritize safety and efficiency in all our products.

    Technical Parameters
    Model no. NBSET-500P-PLUS
    Nominal dehumidifying (27℃ , 60%RH) 500PPD
    Input Voltage 265~277V/ 60Hz
    Rated input power 2.6 Kw
    Rated input current 9.5 A
    Air flow 2800 m³/h
    Applying area (2.6m floor height) 350-500 ㎡
    Humidity control range 40%-95%
    Working temperature 5-38°C
    Net Weight 140 kgs
    Gross weight 160 kgs
    Overall dimension 1750x860x493 mm

    It will be not noticed additionally if any change of above parameters, please contact with us.

    Structure Of Product
    4U[PBB{FR1GMX}KL[MG]

    Use the machine on flat firm floor inside room. Don't put objects in front of air inlet for better efficiency.

    Don't use the machine in the environment with combustible, explosive, corrosive air or dusty. Do keep at least 50cm space for ventilation around the machine.

    Please use the machine away from heat for less power consumption.

    The working temperature range of machine is 5°C ~ 38°C. The protection of compressor will be acted if use it in the environment temperature higher than 38°C and stop running automatically, it will reduce the working life of the machine. Below 5°C, absolute humidity of the environment is quite low, do not use the machine if not necessary.

    Do make sure to leave at least 50 cm from wall to air inlet and at least 50 cm from wall to air outlet when the machine used against a wall, otherwise it will affect the dehumidifying effect or cause machine failure.

    Do not incline the machine exceed 45 degrees in moving or installation. Do correctly assemble the drain pipe for drainage.

    In the low temperature condition, the defrosted water will be frozen gradually at the outlet, please don’t open the machine until all the ice melted to avoid water overflow to room from water collector.

    Please clean the filter net regularly in using machine, make necessary isolation measure when use in the dusty environment to avoid malfunction and raise the working life.

    Don’t cut off the power or pull out plug when machine running. Don’t damage the power line or make any change.

    Don’t put fingers or sticks into the air outlet.

    Don’t do any change of machine unless guiding by our technicians.

    Frequently Asked Questions (FAQ)
    What is the nominal dehumidifying capacity of the NBSET-500P-PLUS?
    The nominal dehumidifying capacity is 500PPD, measured under environmental conditions of 27°C and 60% Relative Humidity (RH).
    What are the ventilation space requirements when installing the dehumidifier?
    You must keep at least 50 cm of clearance space around the machine for proper ventilation. When placing the unit against a wall, ensure there is at least 50 cm of space from both the air inlet and the air outlet to prevent reduced performance or machine failure.
    What is the operating temperature range for this machine?
    The safe working temperature range is between 5°C and 38°C. If the ambient temperature exceeds 38°C, the compressor protection system will automatically shut down the machine to prevent damage. It is not recommended to use the machine below 5°C as the absolute humidity is already very low.
    Can this dehumidifier be used in dusty or hazardous environments?
    No, the machine should not be operated in environments containing combustible, explosive, or corrosive air. If used in a dusty environment, you must clean the filter net regularly and implement necessary isolation measures to prevent malfunctions and extend the machine's lifespan.
    How should the dehumidifier be positioned and handled during installation?
    The unit must be placed on a flat, firm indoor floor. During moving or installation, do not incline the machine by more than 45 degrees. Additionally, ensure the drain pipe is correctly assembled to allow proper drainage.